| (57 intermediate revisions by 2 users not shown) | |||
| Line 2: | Line 2: | ||
==BASICS== | |||
| Line 15: | Line 15: | ||
===ASSIGNEMENT N° 1 - LOUDNESS KILL SWITCH | |||
='''ASSIGNMENTS'''= | |||
==ASSIGNEMENT N° 1 - LOUDNESS KILL SWITCH== | |||
[[File:Assignement1.jpg|608px]] <br> | [[File:Assignement1.jpg|608px]] <br> | ||
MONOSTABLE 555 - MOMENTARY SWITCH<br> | MONOSTABLE 555 - MOMENTARY SWITCH<br> | ||
The "Loudness Kill Switch" reacts to the loudness of music | The first assignment was to build a "super conceptual switch" of any sort. | ||
The "Loudness Kill Switch" reacts to the loudness of music emitted from a speaker. | |||
If the music reaches a certain volume it will switch its self off for a set period of time. | |||
The mechanical construction consists of an aluminum foil wrapped ball hanging freely on a cable in front of a loudspeaker. Positioned in front of the speaker there is a copper rod. | |||
The bass reflex of the music lets the ball swing towards the copper rod and therefore eventually closes the circuit. | |||
The circuit consists of a "555 Timer" in Monostable Mode with it's high and low being inverted. | |||
With the ball and rod acting as a momentary switch triggering the 555 timer. | |||
The 555 timer controls a solid state relay, which powers the amplifier serving as a music output to the speaker. | |||
The sensitivity of this conceptual switch can be adjusted by simply moving the copper rod closer or further from the speaker. The time the music shall stay mute can be adjusted through the resistor used on the 555 timer (we usually had it set to 30 sec.). | |||
This contraption can be on one hand viewed as a practical device, which in some form could come in handy for living with noisy flatmates... | |||
for us the circuit its self is the interesting part. Converting electric power to mechanical, | |||
and in the end the system feedbacking on itself, or rather limiting itself as soon as life starts being fun | |||
[[File:SKETCH.jpg|608px]] | [[File:SKETCH.jpg|608px]] | ||
[[File:BALL AND CIRCUIT.JPG|200px]] | [[File:BALL AND CIRCUIT.JPG|200px]] | ||
| Line 35: | Line 50: | ||
[[File:BALL_AND_ROD.JPG|200px]] | [[File:BALL_AND_ROD.JPG|200px]] | ||
<br> | <br> | ||
Parts: | Parts: | ||
Styrofoam ball wrapped with aluminium foil | | Styrofoam ball wrapped with aluminium foil | | ||
| Line 43: | Line 56: | ||
Solid State Relay | | Solid State Relay | | ||
Loudspeaker | | Loudspeaker | | ||
Amplifier | Amplifier | | ||
{{#ev:vimeo|101017288}} | |||
---- | ---- | ||
<br> | |||
==ASSIGNEMENT N° 2 - VEHICLE, MODEL N° 1== | |||
[[File:Assignement2_1.jpg|608px]] | [[File:Assignement2_1.jpg|608px]] | ||
| Line 56: | Line 72: | ||
ASTABLE 555 - PHOTODIODE as a SWITCH | ASTABLE 555 - PHOTODIODE as a SWITCH | ||
After having learnt about the IC 741 aka the comparator circuit, it was our goal to utilize this in our second assignment. The other parts we were able to scavenge across the classroom. Two motors attached to the breadboard transformed our circuit into a little vehicle. | |||
The comparator circuit was controlled through a photo resistor. Depending on the amount of light hitting the photo resistor the state would be either high or low. A relay set up as an H-Bridge would transfer high and low two forward or backward movement of the motors. | |||
Originally we wanted to mirror this circuit on the breadboard so both motors could be controlled independently. Unfortunately we were missing a second Transistor (TIP-127) to be able to finalize our plans that weekend. | |||
Although not being able to complete our second assignment to the extend we had originally imagined, we somehow had the feeling our vehicle was developing it's own character in a way. | |||
e.g. it could be programmed to be shy of the dark, and stop driving when it leaves a well lit space. | |||
The jerkyness it had when changing directions, or it staying upright through it's low center of gravity somehow added to this impression. | |||
| Line 67: | Line 84: | ||
[[File:Ass2_2.jpg|200px]] | [[File:Ass2_2.jpg|200px]] | ||
[[File:Ass2_1.jpg|200px]]<br> | [[File:Ass2_1.jpg|200px]]<br> | ||
COMPONENTS: | |||
1x | 1x | ||
Double Pole Double Throw - Relay | | Double Pole Double Throw - Relay | | ||
| Line 77: | Line 93: | ||
Battery | | Battery | | ||
{{#ev:vimeo|101016951}} | |||
---- | ---- | ||
<br> | <br> | ||
==ASSIGNEMENT N° 3 - DRAWING MACHINE== | |||
[[File:Assignment3.jpg|608px]] | [[File:Assignment3.jpg|608px]] | ||
| Line 89: | Line 105: | ||
ASTABLE 555 - RESISTORS as SWITCHES | ASTABLE 555 - RESISTORS as SWITCHES | ||
For our third assignment, instead of starting from scratch – we decided to continue working on our vehicle as we had become quite fond of it. | |||
The main question was; what could this vehicle do? | |||
The answer came quickly. With a pen or felt tip attached it could become a simple drawing machine. | |||
Whilst making the vehicle its self more sturdy with a metal framing – concidering the cricuit we took a step back. Instead of it being reactive to light through the comparator it was controlled by two 555 timers. Now each motor could act independently. With it not being reactive we could analyze the patterns better that it would produce. The patterns depend on the timing of the ICs and therefor could be altered by changing the resistors and capacitors on the breadboard. | |||
<br> Parts: | In a further step we are considering combining the Assignments 2&3. | ||
the drawing machine could become reactive again. Ideally it would still produce recognizable patterns, but vary these once the lighting situation changes. | |||
Also finding a different drawing tool, so the vehicle doesn't have to be limited to a sheet of paper would be something to take into account. | |||
[[File:VEHICLE TOP.jpg|300px]] | |||
[[File:SPIRALE.jpg|300px]]<br> | |||
[[File:VEHICLE LEFT.jpg|300px]] | |||
[[File:1st_Test.jpg|300px]]<br> | |||
Parts: 2x Double Pole Double Throw - Relay | TIP 122 | | |||
555 Timer | | |||
3x Battery | | |||
<br> | |||
<br> | |||
---- | |||
<br> | <br> | ||
=SUMMAERY - PRESENTATION= | |||
[[File:Pres4.jpg|200px]] | [[File:Pres4.jpg|200px]] | ||
[[File:Pres2.jpg|200px]] | [[File:Pres2.jpg|200px]] | ||
[[File:Pres3.jpg|200px]] | [[File:Pres3.jpg|200px]] | ||
Exhibition photos ♡ 2014 by Alice Dziewinski. | |||
{{#ev:vimeo|101011710}} | |||
Latest revision as of 12:33, 13 February 2019
DEVICES OF PERCEPTION
BASICS
ASSIGNMENTS
ASSIGNEMENT N° 1 - LOUDNESS KILL SWITCH
MONOSTABLE 555 - MOMENTARY SWITCH
The first assignment was to build a "super conceptual switch" of any sort.
The "Loudness Kill Switch" reacts to the loudness of music emitted from a speaker. If the music reaches a certain volume it will switch its self off for a set period of time.
The mechanical construction consists of an aluminum foil wrapped ball hanging freely on a cable in front of a loudspeaker. Positioned in front of the speaker there is a copper rod. The bass reflex of the music lets the ball swing towards the copper rod and therefore eventually closes the circuit. The circuit consists of a "555 Timer" in Monostable Mode with it's high and low being inverted. With the ball and rod acting as a momentary switch triggering the 555 timer. The 555 timer controls a solid state relay, which powers the amplifier serving as a music output to the speaker. The sensitivity of this conceptual switch can be adjusted by simply moving the copper rod closer or further from the speaker. The time the music shall stay mute can be adjusted through the resistor used on the 555 timer (we usually had it set to 30 sec.).
This contraption can be on one hand viewed as a practical device, which in some form could come in handy for living with noisy flatmates... for us the circuit its self is the interesting part. Converting electric power to mechanical, and in the end the system feedbacking on itself, or rather limiting itself as soon as life starts being fun
Parts:
Styrofoam ball wrapped with aluminium foil |
Copper rod |
555 Timer |
Solid State Relay |
Loudspeaker |
Amplifier |
ASSIGNEMENT N° 2 - VEHICLE, MODEL N° 1
ASTABLE 555 - PHOTODIODE as a SWITCH
After having learnt about the IC 741 aka the comparator circuit, it was our goal to utilize this in our second assignment. The other parts we were able to scavenge across the classroom. Two motors attached to the breadboard transformed our circuit into a little vehicle. The comparator circuit was controlled through a photo resistor. Depending on the amount of light hitting the photo resistor the state would be either high or low. A relay set up as an H-Bridge would transfer high and low two forward or backward movement of the motors. Originally we wanted to mirror this circuit on the breadboard so both motors could be controlled independently. Unfortunately we were missing a second Transistor (TIP-127) to be able to finalize our plans that weekend.
Although not being able to complete our second assignment to the extend we had originally imagined, we somehow had the feeling our vehicle was developing it's own character in a way. e.g. it could be programmed to be shy of the dark, and stop driving when it leaves a well lit space. The jerkyness it had when changing directions, or it staying upright through it's low center of gravity somehow added to this impression.
COMPONENTS:
1x
Double Pole Double Throw - Relay |
TIP 127 |
741 Comparator |
Photodiode |
2x
Battery |
ASSIGNEMENT N° 3 - DRAWING MACHINE
We used the same circuit twice to run the two motors
ASTABLE 555 - RESISTORS as SWITCHES
For our third assignment, instead of starting from scratch – we decided to continue working on our vehicle as we had become quite fond of it.
The main question was; what could this vehicle do? The answer came quickly. With a pen or felt tip attached it could become a simple drawing machine. Whilst making the vehicle its self more sturdy with a metal framing – concidering the cricuit we took a step back. Instead of it being reactive to light through the comparator it was controlled by two 555 timers. Now each motor could act independently. With it not being reactive we could analyze the patterns better that it would produce. The patterns depend on the timing of the ICs and therefor could be altered by changing the resistors and capacitors on the breadboard.
In a further step we are considering combining the Assignments 2&3. the drawing machine could become reactive again. Ideally it would still produce recognizable patterns, but vary these once the lighting situation changes. Also finding a different drawing tool, so the vehicle doesn't have to be limited to a sheet of paper would be something to take into account.
Parts: 2x Double Pole Double Throw - Relay | TIP 122 |
555 Timer |
3x Battery |
SUMMAERY - PRESENTATION
Exhibition photos ♡ 2014 by Alice Dziewinski.