GMU:3DIY/Printer queue: Difference between revisions

From Medien Wiki
No edit summary
Line 46: Line 46:
|
|
|
|
|extremes Warping in der Spitze
|extreme warping on the spire
|größerer Ausdruck, Luftzufuhr in der kritischen Phase, Pfeile und Schleifpapier
|higher print resolution, cooldown by fan in the critical phase, rasp and sand paper
|[[File:Test_01.jpg|right|thumb|150px|]]
|[[File:Test_01.jpg|right|thumb|150px|]]
|-
|-
Line 59: Line 59:
|
|
|
|
|verbesserter Testdruck, basierend darauf Ausdrucken des kompletten Animationszyklus aus 16 Einzelbildern
|improved testprint, based on this, we startet printing the complete animation cycle of 16 frames
|[[File:Test_02.jpg|right|thumb|150px|]]
|[[File:Test_02.jpg|right|thumb|150px|]]
|-
|-
|
|
|animationcycle01.bfb
|animationcycle01.bfb (Frame 1-4)
|26.8.
|26.8.
|approx 140 minutes
|Robert S. und Florian M.
|
|
|Robert S. und Florian M.
|
|
|
|
|
|
|
|
|Frame 1-4
|[[File:framea.jpg|right|thumb|150px|]]
|[[File:Animation_01.jpg|right|thumb|150px|]]
|-
|-
|
|
|animationcycle02.bfb
|animationcycle02.bfb (Frame 5-7 +12)
|30.8.
|30.8.
|
|approx 140 minutes
|Robert S. und Florian M.
|Robert S. und Florian M.
|
|
Line 83: Line 83:
|
|
|
|
|Frame 5-7 +12
|
|
|[[File:frameb.jpg|right|thumb|150px|]]
|-
|-
|
|
|animationcycle03.bfb
|animationcycle03.bfb (Frame 8-11)
|31.8.
|31.8.
|
|approx 140 minutes
|Robert S. und Florian M.
|Robert S. und Florian M.
|
|
Line 95: Line 95:
|
|
|
|
|Frame 8-11
|
|
|[[File:framec.jpg|right|thumb|150px|]]
|-
|-
|
|
|animationcycle04.bfb
|animationcycle04.bfb (Frame 13-14)
|1.9.
|1.9.
|
|approx. 60 minutes
|Robert S. und Florian M.
|Robert S. und Florian M.
|
|
Line 107: Line 107:
|
|
|
|
|Frame 13-14
|
|
|[[File:framed.jpg|right|thumb|150px|]]
|-
|-
|
|
|animationcycle05.bfb
|animationcycle05.bfb (Frame 15-16)
|2.9.
|2.9.
|
|
|Robert S. und Florian M.
|Robert S. und Florian M.
|approx. 60 minutes
|
|
|
|
|
|
|
|
|Frame 15-16
|[[File:framee.jpg|right|thumb|150px|]]
|
|-
|-
|
|
|animationcycle05.bfb
|zoetrope_cap.bfb (cap of the zoetrope)
|15.9.-16.9.
|15.9.-16.9.
|
|approx. 10 hours till abortion
|Robert S. und Florian M.
|Robert S. und Florian M.
|
|
|
|
|
|
|ungenaues Printbed erschwert druck auf größe 20x20, abs verzieht bei großen flächen extrem (hohe temperatur?).
|imprecise printbed complicates printing of large objects (20x20x1cm), ABS warps too much (high temperature?)
 
So große Sachen mit ABS zu drucken ist schwer, versucht PLA --[[User:Matthias.breuer|Matthias.breuer]] 14:37, 22 September 2010 (CEST)
So große Sachen mit ABS zu drucken ist schwer, versucht PLA --[[User:Matthias.breuer|Matthias.breuer]] 14:37, 22 September 2010 (CEST)
|Deckel des Zoetrops
|optimizing the .stl file, trying the same with PLA
|
|
|-
|-
|
|
|animationcycle05.bfb
|zoetrope_cap.bfb (cap of the zoetrope)
|21.9.
|21.9.
|approx. 20 minutes
|Robert S. und Florian M.
|
|
|Robert S. und Florian M.
|
|
|
|
|problems with the .stl file and imprecise printbed obviate the 2nd try while printing the raft and lead to an early stop 
|
|
|fehlerhafte .stl datei und ungenaues Printbed verhindern den 2. Versuch bereits beim Drucken des Rafts.
|Deckel des Zoetrops - Versuch 2
|
|
|-
|-
|}
|}
Retrieved from "https://www.uni-weimar.de/kunst-und-gestaltung/wiki/GMU:3DIY/Printer_queue"