GMU:3DIY/Printer queue: Difference between revisions

From Medien Wiki
Line 193: Line 193:
|
|
|[[File:Crank_handle_part1.JPG|right|thumb|150px|]]
|[[File:Crank_handle_part1.JPG|right|thumb|150px|]]
|-
|
|gearshell.bfb (part of the gear)
|26.10.
|
|Robert S. und Florian M.
|
|several hours (only troubleshooting
|
|problems with the printbed level (was too close to extruder), flakes of PLA were sometimes extruded together with the ABS
|leveling the bed, cleaning the extruder
|no acceptable result, therefore nothing to photograph
|}
|}

Revision as of 07:53, 27 October 2010

the printer has found it's new home and is sort of available. the room can for the moment be booked via me.

so, the next step will be the one you are all craving for: printing! fair enough and you shall do so, but as none of us has much experience it would be nice if you would document your printing and the tricks and tweak you find out. here is the perfect place for this.

please document your printer usage and your experiences. the printer queue is a schedule, where you can sign in for printing. with your name, the name and a picture of the thing you are going to print, the estimated print time. And when you are done a print report: featuring the settings you used, the time and amout of material it took, what issues you came across, how you fixed it ... the amount of material you used...

remember to always obey the two rules: 
do not break anything! 
do not hurt yourself!

The printer queue

Image of file File Name Print date and time Name Print report (Material, temperature, time, feed rate, etc.) Amount of time needed Amount of material used Issues Fixes Image of printed object
.jpg des File
Datei Name Druck Datum und Uhrzeit Name Druckbericht (Material, Temperatur, Zeit, Vorschub, etc.) Gebrauchte Zeit Verbrauchte Menge an Material Probleme Und wie sie gelöst wurden
.jpg des gedruckten Objekts
test.bfb 25.8. Robert S. und Florian M. extreme warping on the spire higher print resolution, cooldown by fan in the critical phase, rasp and sand paper
Test 01.jpg
test2.bfb 26.8. Robert S. und Florian M. improved testprint, based on this, we startet printing the complete animation cycle of 16 frames
Test 02.jpg
animationcycle01.bfb (Frame 1-4) 26.8. Robert S. und Florian M. approx 140 minutes
Framea.jpg
animationcycle02.bfb (Frame 5-7 +12) 30.8. Robert S. und Florian M. approx 140 minutes
Frameb.jpg
animationcycle03.bfb (Frame 8-11) 31.8. Robert S. und Florian M. approx 140 minutes
Framec.jpg
animationcycle04.bfb (Frame 13-14) 1.9. Robert S. und Florian M. approx. 60 minutes
Framed.jpg
animationcycle05.bfb (Frame 15-16) 2.9. Robert S. und Florian M. approx. 60 minutes
Framee.jpg
zoetrope_cap.bfb (cap of the zoetrope) 15.9.-16.9. Robert S. und Florian M. approx. 10 hours till abortion imprecise printbed complicates printing of large objects (20x20x1cm), ABS warps too much (high temperature?) optimizing the .stl file, trying the same with PLA
Zoe cap.jpg
zoetrope_cap.bfb (cap of the zoetrope) 21.9. Robert S. und Florian M. approx. 20 minutes problems with the .stl file and imprecise printbed obviate the 2nd try while printing the raft and lead to an early stop no existing image of this try
Eindrucken Variante 2 29.09.2010 Katharina E. Due to the extensive work needed preparing the LEDs the test print will be the final print.
3DIY LED-eindrucken Variante2 .jpg
|-
zoetrope_cap_pla.bfb (cap of the zoetrope with pla settings) 28.9.-29.9. Robert S. und Florian M. approx. 8hours structure was a bit week and the material feed was blocked due to mechanical problems with the PLA material roll (approx 30minutes of printing without material(!), cause the extrusion was kind of blocked) slightly higher printing temperature might help, fixing the problems with the material roll will be necessary.
Cap.jpg
#
zoetrope_lamp.bfb (construction for the led lamp) 29.9. Robert S. und Florian M. approx. 2hours everything went perfectly fine
Lamp.jpg
crankhandle_p1.bfb (part of the gear) 13.10. Robert S. und Florian M. approx. 20 minutes everything went perfectly fine
Crank handle part1.JPG
gearshell.bfb (part of the gear) 26.10. Robert S. und Florian M. several hours (only troubleshooting problems with the printbed level (was too close to extruder), flakes of PLA were sometimes extruded together with the ABS leveling the bed, cleaning the extruder no acceptable result, therefore nothing to photograph