513
edits
GMU:Sensor Hacklab/Christian Doeller (view source)
Revision as of 08:19, 1 August 2016
, 1 August 2016no edit summary
No edit summary |
No edit summary |
||
| Line 208: | Line 208: | ||
I kept all the cut out pieces in order to change the design as I need it by putting them back in place.<br><br> | I kept all the cut out pieces in order to change the design as I need it by putting them back in place.<br><br> | ||
[[File:Raster_Styro.jpg]]<br><br> | |||
| Line 216: | Line 216: | ||
The bottom part features eight and the upper part features six „circuit lanes“ that are located in a way so that they form a kind of matrix-grid when they are put on top of each other. <br> | The bottom part features eight and the upper part features six „circuit lanes“ that are located in a way so that they form a kind of matrix-grid when they are put on top of each other. <br> | ||
Raster_Karton.jpg <br><br> | [[File:Raster_Karton.jpg]] <br><br> | ||
Zeichnung_Karton.jpg | [[File:Zeichnung_Karton.jpg]]<br><br> | ||
Zeichnung_Karton2.jpg | [[File:Zeichnung_Karton2.jpg]]<br><br> | ||
Zeichnung_Karton3.jpg | [[File:Zeichnung_Karton3.jpg]]<br><br> | ||
Alu_Karton.jpg | [[File:Alu_Karton.jpg]]<br><br> | ||
Raster_Alu_Karton.jpg | [[File:Raster_Alu_Karton.jpg]]<br><br> | ||
Alu_Karton2.jpg | [[File:Alu_Karton2.jpg]]<br><br> | ||
I first planned to use a resistor ladder for the Analog input pin of the arduino in order to minimize the amount of pins being used.<br><br> | I first planned to use a resistor ladder for the Analog input pin of the arduino in order to minimize the amount of pins being used.<br><br> | ||
Schematic_Raster_Styro.jpg | [[File:Schematic_Raster_Styro.jpg]]<br><br> | ||
Alu_Resistor_Ladder.jpg | [[File:Alu_Resistor_Ladder.jpg]]<br><br> | ||
Alu_Resistor_Ladder2.jpg | [[File:Alu_Resistor_Ladder2.jpg]]<br><br> | ||
As this did not work out (too many delays in the code, too slow, a lot of noise) I changed the design by attaching a separate wire to each of the eight „circuit lanes“ that go to the Arduinos digital input.<br> | As this did not work out (too many delays in the code, too slow, a lot of noise) I changed the design by attaching a separate wire to each of the eight „circuit lanes“ that go to the Arduinos digital input.<br> | ||
| Line 234: | Line 234: | ||
Arduino_Raster_Karton.jpg | [[File:Arduino_Raster_Karton.jpg]]<br><br> | ||
| Line 246: | Line 246: | ||
http://playground.arduino.cc/Code/Keypad | [http://playground.arduino.cc/Code/Keypad] <br> | ||
http://www.dummies.com/how-to/content/how-to-specify-userdefined-functions-for-your-keyp.html | [http://www.dummies.com/how-to/content/how-to-specify-userdefined-functions-for-your-keyp.html]<br><br> | ||
Arduino_Raster_Matrix_Carpet.png | [[File:Arduino_Raster_Matrix_Carpet.png]]<br><br> | ||